This Speed Sensor was designed specifically for the WarP series of motors with a tailshaft diameter of .875" and replaces the Zolox Speed Sensor. However, the kit could fit any motor with an exposed tail shaft.
$95
We offer both a clutchless and an adaptor plate that retains the clutch. The clutch adaptor plate is pre-cut and pre-drilled to match your transmission's bell housing for a clean, professional look. Just provide your vehicles make and model and we'll send you everything you need to couple your old transmission to your new motor.
$775
Motor Mount
Designed specifically for either a WarP 9 or FB-4001 motor, these mounts compress the motor into place and have flanges for mounting to most rear-wheel drive vehicles. Powder coated and extremely durable.
$180
Shunt 50mV
A shunt is a resistor that is wired in series with your load allowing you to monitor the amperage in your system.
Fast-Acting 600V fuse for an EV's high voltage accessory components.
$15
Ferraz Shawmut Fuse Blocks accommodate all 0 to 30 ampere fuses. Insulators are glass-filled polycarbonate (GFPC) with verified dielectric strength in excess of 2500V. Fuse blocks feature a unique adder block which can be snapped onto 1-, 2- or 3-pole blocks to form multi-pole segmented blocks of as many poles as desired. All fuse clips are made of high conductivity tin-plated copper alloy.
High Current Fuse
Ferraz 300 Volt 500 Amp fuse is essential in any electric vehicle conversion. This fast acting semiconductor fuse will help protect the controller and occupants from harm in the event of any malfunction. Recommended for all Curtis, WarP Drive (1000A), and the Zilla LV controllers.
Ferraz Shawmut fuse blocks for the 300VDC 500A fuses are glass-filled polycarbonate or laminated phenolic insulator blocks with studs to accommodate bolt-in fuses. All studs, clips and mounting hardware are tin or zinc plated.
Magna Lugs
MagnaLug® Starter/Ground Lug.
Made of 100% copper.
Tin-plated twice the thickness as industry standards.
MagnaLugs® use same crimp setting as battery terminals.
80% thicker walls for greater strength and conductivity.
UL listed & exceeds SAE conductivity standards.
Wider pads for better electrical contact.
$2.50
Ultra-Flex Welding Cable
Using this flexible cable will help keep the strain off of your battery terminal posts and provide for easier installation. American Made, EPDM jacketed cable which provides “noodle-like” performance. Jacket is: Oil, Flame, Abrasive, Water, Tear, Grease and Cut Resistant.
Welding Cable
This cable comes with an inner safety liner of an opposite color, not a cheap paper wrap. Meets or exceeds all welding cable specifications and amperage. Acid, gas, oil, sunlight (ozone), flame, and water resistant. Cable is extremely abrasion resistant.
2/0 Battery
Terminal Boot
Flexible rubber battery terminal covers protect your terminals from contact with unwanted surfaces preventing shorts and insuring safety.
$1.75
Curtis PB-6 Potbox
A Potbox provides communication between the gas pedal and the controller, converting mechanical energy (your foot on the gas pedal) to electrical energy which the controller can then interpret and pass onto the motor. The Curtis PB-6 has been an industry favorite for years.
Designed for use on larger higher current electric vehicles, industrial trucks, etc. Additionally, for use on static power systems as a LVD for system battery protection.
Rated at 250 amps continuous for severe switching applications or 400 amps for light duty switching applications.
In case of any impact the inertia switch will trip and disconnect power to the main contactor, adding another level of safety to your EV. This is essential when dealing with a high voltage electric vehicle.
$52
ANDERSON 'SB' CONNECTORS
The innovative SB® connectors provide
cost-effective reliability, design flexibility and
safety for your products' manufacture,
installation and maintenance.
APP's 2 pole connector is available with a 50
amp rating, 600 Volts continuous AC or DC
operation.
There are SB® connectors for
many applications and wire sizes, #6 to #16
AWG (13.3 to 1.3 mm²). Mechanical keys
ensure connectors will only mate with
connectors of the same color. Different color
housings are selected to identify voltages,
thus preventing mismatching of the power
supply system.
SB-50
(Consists of 1 housing and 2 contacts)
SB-175
(Consists of 1 housing and 2 contacts)
SB-350
(Consists of 1 housing and (2) 2/0 contacts)
$7
$14
$22
Contact Set
These contacts are replacements for the Anderson SB-50, SB-175, SB-350 connectors.
SB Housing
Single housing for the SB-50, SB-175, SB-350
SB-350 Release Handle w/ Strain Relief
Easily disconnect your high voltage wires with this professional release handle made by Anderson. Built in cable strain relief and heavy-duty, powder-coated steel will ensure long lasting and and safe disconnects on your vehicle.
$55
SB-350, SB-175 Release Handle
Easily disconnect your high voltage wires with this professional release handle made by Anderson. Made of heavy-duty, powder-coated stee these release handles will ensure long lasting and and safe disconnects on your vehicle.
A low cost and simple solution to disconnecting your high voltage wires.
$8.50
Heat Shrink
A high quality heat shrink made of polyolefin. It has a 3:1 shrink ratio and a build in adheasive that when heated, it creates a waterproof connection and a perfectly sealed internal environment. It remains flame retardant, and is very flexible.
